Replacement Coil?

Dan,

If your meter is accurately calibrated then it seems to me that your
voltages are on the low side. Typical good battery voltage is around 12.5
to 12.7 volts. At least that's what I typically see on all of our vehicles.


The one reading I didn't see below was the coil voltage while you were
cranking the engine. If the voltage drops to much while cranking you'll
have weak or no spark.

The other thing to look at would be your grounding. A good ground can make
a huge difference.

Brad


On Tue, Aug 31, 2010 at 11:17 AM, ramblerdan <



> Still tearing my hair out over this ignition problem. Using an
> incandescent-bulb tester, I see a spark that is intermittent and weak. Have
> replaced the coil twice and the Pertronix module once. Cap, wires, and rotor
> are new. Cap has no cracks or evidence of arcing that I can see, and no
> cruddy buildup anywhere. Coil is now wired backward, as recommended.
>
> With ignition off, battery shows 12.2V.
>
> With ignition on but engine not tuning, the battery shows 11.7 volts—subpar
> I know, but enough to matter? It still cranks the engine nicely.
>
> Ignition relay to ground with coil disconnected: 11.7V (same as battery),
> so I think that rules out resistance in the relay.
>
> Ignition relay side of coil to ground: 10V
>
> (+) to (-) posts on coil: 8.8V
>
> I can't find these sort of specs in the Amphi shop manual. Do those numbers
> sound reasonable? I'll pull the plugs again today (they're probably wet from
> cranking without running), but even if the plug were fouled, wouldn't the
> tester show a spark?
>
>
>
 
I stock replacement screw in coils and also have just the screw in part.

The charging system and starter must be up to par for everything to work as it should.
a lot of times you can crank a motor over and no start, as soon as you let off the key it then has enough umpha and away it goes,
or just a extra boost with jumpers and 1 rev later away it goes.,
Gord S.
 
Thanks guys. Will check voltage at coil while cranking and report back.

I subsequently charged the battery up to about 12.4V, checked the plugs (fine), and smell gas in the carb, but still no joy. Will try simultaneously jumping from another car to push the voltage up to optimum and see where that gets us.

Did the 8.8V from (-) to (+) on the coil sound reasonable? Have converted to press-on wires, BTW.
 
Dan,

Not sure how to read the 8.8 volts. If you were connecting from the -
terminal of the coil to the + terminal of the coil I'm not sure just what
that indicates. Assuming you're setup for negative ground you would be using
the path through the pertronix to create a ground for your meter reading.

If you were reading from coil + terminal to a true ground then it would
indicate the pertronix is "closed" and the coil is dropping the voltage from
12.2 down to 8.8. That seems like a pretty large drop. I really don't
know what the voltage drop should be a cross a coil when the points or
pertronix is in the closed state.

It will be interesting to see what you get when you boost the voltage with
jumper cables from a running vehicle.

Brad


On Wed, Sep 1, 2010 at 3:02 PM, ramblerdan
<>wrote:


> Thanks guys. Will check voltage at coil while cranking and report back.
>
> I subsequently charged the battery up to about 12.4V, checked the plugs
> (fine), and smell gas in the carb, but still no joy. Will try simultaneously
> jumping from another car to push the voltage up to optimum and see where
> that gets us.
>
> Did the 8.8V from (-) to (+) on the coil sound reasonable? Have converted
> to press-on wires, BTW.
>
>
>
 
Make sure your ground wire is 100%. A bad ground can lead to many mysterious ailments.

I would suggesting swapping out the pertronix for old fashioned points until you get the problem resolved. The Pertronix may have been fried and it also introduces another unknown variable.

Is the distributor timing correct? I once had a Brit car specialist spend 2 weeks diagnosing a no start which turned out to be a distributor that had turned 180 degrees.
 
Update

Jumped it today, and it started right up! Prior to the jump-start, the voltage across the coil terminals while cranking was a mere 5.5V.

BTW the car is positive-ground, and the coil's negative terminal is wired directly to ground (yes backward, but if Dave the Wave says that's the way to go, I listen), so connecting to the coil terminal or ground per se yields an identical reading. The ground connections are good; I even added a ground strap on the transmission.

Once the car started running, the digital voltmeter went crazy, so it appears that the alternator is not putting out clean DC. A marginal battery and malfunctioning alternator explains why the car would run for an hour or so and then konk out (in the water, naturally).

I think the alternator is an aftermarket conversion (Amphis came with generators, yes?) with no paperwork, so I'll take it to a local rebuild shop to have them fix the rectifier and, if the voltage regulator is internal, that too.

Thanks all for your input!
 
A further comment about grounding.

The current path during engine cranking is from the battery negative,
through the starter relay, through a heavy cable to the starter motor
terminal, through the starter motor windings to the starter motor housing,
then to the starter mounting on the bell housing casting, then to the
transmission case, along the length of the transmission case, across a
flexible bond strap to the hull, back through the hull to the battery ground
post, and finally back through the battery cable to the battery positive
terminal. Whew!

Every interface joint along that path can create an impediment to current
flow. Every conductive part (wires, bolts, castings, sheet metal) also can
impede current flow. You job, should you choose to accept it, is to make
sure that current path has no bad parts and joints.

I think it would make a whole lot more sense to shorten that path as much as
possible. I would run the battery ground cable first to a good ground point
directly on the engine, or perhaps use one of the bell housing bolts. From
that bolt, I would then run a heavy cable to the hull ground stud.

This doesn't cure everything electrical, but it certainly helps the
starting, ignition and generator systems.


Ed Price
IAOC Membership Registrar
El Cajon, CA USA
WB6WSN
1961 Amphicar 770
1987 MB 420SEL





_____

From: bkahler [mailto:]
Sent: Tuesday, August 31, 2010 11:44 AM
To: edprice@cox.net
Subject: RE: [General Amphicar Discussion-t-20062] Re: Replacement Coil?


Dan,

If your meter is accurately calibrated then it seems to me that your
voltages are on the low side. Typical good battery voltage is around 12.5
to 12.7 volts. At least that's what I typically see on all of our vehicles.


The one reading I didn't see below was the coil voltage while you were
cranking the engine. If the voltage drops to much while cranking you'll
have weak or no spark.

The other thing to look at would be your grounding. A good ground can make
a huge difference.

Brad
 
Top